How to Make a Child’s Easel (Wood or Cardboard)

How to Make a Child's Easel (Wood or Cardboard) – PaintingProGuide cover image

A kid who paints flat on the kitchen table ends up with a smeared sleeve, a cramped wrist and a picture that is hard to see as a whole. Standing the work up fixes all three, and you do not need to spend much to do it. This guide covers how to make a child’s easel two ways: a sturdy wooden A-frame that can last for years, and a fast cardboard tabletop version you can finish in an afternoon nap window.

Quick answer: For a wooden child’s easel, build two identical leg frames from 1×2 or 1×3 pine about 40 to 44 inches long, join them at the top with two hinges, fix a 24 x 24 inch hardboard or plywood panel to the front frame, add a 3 to 4 inch paint tray at about the child’s elbow height, and tie the legs with a cord or chain so they cannot splay. For a cardboard version, fold a sheet of double-wall corrugated board into a triangular prism, tape the seams, and clip paper to the front face. The wooden build takes 3 to 4 working hours plus finish drying; the cardboard one takes about 45 minutes.

Before cutting anything, it helps to know why the upright position matters at all. Our explainer on why an easel is worth it for young children goes into posture, shoulder movement and the way a vertical surface changes how kids draw. If you decide a homemade frame is not for you, the ready-made options in our roundup of kids easels with a magnetic board show what the commercial versions add.

Pick Your Build: Wood or Cardboard

The two builds solve different problems. A wooden A-frame stands on the floor, holds a heavy board, survives being leaned on and can carry chalkboard or magnetic surfaces. A cardboard easel sits on a table, weighs almost nothing and costs close to zero, but it will soften if a toddler floods it with water.

FactorWooden A-frameCardboard tabletop
Typical working time3 to 4 hours, plus 1 to 3 days for finishes30 to 60 minutes
Tools neededSaw, drill, sander or sandpaper, screwdriverBox cutter, ruler, tape, glue
Best agesAbout 2 to 8, with height tweaksAbout 3 and up, with supervision of the cutter
Surfaces possiblePaper, chalkboard paint, magnetic sheet, dry-erase panelPaper only (or a taped-on whiteboard sheet)
Handles wet paintYes, once sealedLight washes only; warps when soaked
LifespanYearsWeeks to a few months

If your child is still in the stage of mostly crayons and stickers, start with cardboard. If you already know paint, chalk and magnets will all get used, the wooden version pays back the effort.

How to Make a Child’s Easel From Wood

The design below is the classic double-sided A-frame you see in preschool classrooms, scaled for a home. Both sides can carry a board, but you can start with one and add the second later.

Measure the Child First

Height is the detail most DIY plans skip. Have your child stand straight and note two numbers: the height of their elbow and the height of the top of their head. The paint tray should sit roughly at elbow height, and the top edge of the drawing panel should land about at the top of the head or a few inches above it. That way the child can reach every part of the surface without stretching on tiptoe.

As a rough guide, many 3-year-olds have an elbow height near 24 to 26 inches, and many 6-year-olds sit closer to 28 to 32 inches. Children grow quickly, so set the tray an inch or two high rather than low, and plan an adjustable step (covered below) if you want the easel to last several years.

Materials List

  • 4 pieces of 1×2 or 1×3 pine, each 40 to 44 inches long (the legs)
  • 4 pieces of the same stock, each 22 inches long (top and lower cross rails)
  • 2 panels of 1/4 inch hardboard or birch plywood, 24 x 24 inches
  • 2 pieces of 1×4, each 24 to 26 inches long (paint trays), plus 2 strips of 1/2 x 3/4 inch trim for the tray lip
  • 2 butt hinges, about 2 to 3 inches
  • 1 length of chain or strong cord, about 18 to 24 inches, with 2 screw eyes
  • Wood glue and 1-1/4 inch wood screws
  • Sandpaper in 120, 180 and 220 grit
  • Primer and a low-VOC, water-based paint or clear finish
  • Optional: chalkboard paint, magnetic primer or a thin galvanized steel sheet, dry-erase panel, two bulldog clips

Step 1: Cut and Round Everything (about 45 minutes)

Cut the four legs and four rails to length. Then round every exposed corner. A small child will bump into this frame at face height, so take a sanding block or a router with a small roundover bit to the top ends of the legs, the outer corners of the tray and the panel corners. Trace a coin on each panel corner and sand down to the line; that gives a consistent radius of about half an inch.

Step 2: Build Two Ladder Frames (about 45 minutes)

Lay two legs parallel, about 22 inches apart on the outside. Glue and screw one rail flush with the top and a second rail about 12 inches up from the floor. That lower rail stiffens the frame and gives the tray something to rest on later. Check for square by measuring both diagonals; they should match within about 1/8 inch. Repeat for the second frame.

Pre-drill every screw hole. Pine splits easily near the end of a board, and a split leg is the most common reason a homemade easel wobbles.

Step 3: Hinge the Tops (about 15 minutes)

Stand the two frames face to face so the top rails touch. Fit one hinge near each end of the top rails, with the hinge knuckle on top. When the frames open, the legs should spread to about 18 to 22 inches at the floor for a 42 inch leg. Wider is steadier but takes more floor space; narrower is easier to tip.

Step 4: Add the Splay Stop (about 10 minutes)

This is the safety step people skip. Without something linking the front and back legs, a child leaning on the board can push the frame flat. Drive a screw eye into the inside edge of one front leg and the matching back leg, about 15 inches from the floor, and connect them with chain or cord so the spread is fixed. Repeat on the other side. Some builders use a folding wooden brace instead; either works as long as the legs cannot open past the set angle.

Step 5: Mount the Panels (about 20 minutes)

Glue and screw a panel to the outside face of each frame, top edge flush with the top rail or slightly above it. Countersink the screws so the heads sit below the surface. If you plan to use chalkboard paint, fill the screw holes with wood filler and sand them flush now, because chalk catches on every dimple.

Step 6: Build the Paint Trays (about 30 minutes)

Glue a strip of trim along the front edge of each 1×4 to create a lip about 1/2 inch tall. That lip stops crayons and paint cups sliding off. Attach each tray to the legs at the elbow height you measured, using two screws per side. A tray around 3-1/2 inches deep holds a standard spill-proof paint cup; anything shallower turns into a crayon-only shelf.

Step 7: Finish and Cure (1 to 3 days)

Sand everything to 220 grit, wipe off dust and apply a primer and two thin coats of water-based paint or clear finish. Choose a product labeled for children’s furniture or toys if you can, and let it cure for the full time listed on the can before the easel goes into use; surface-dry is not the same as cured.

Adding Chalkboard, Whiteboard or Magnetic Surfaces

The panel is where a homemade easel can match a store-bought one. Each surface needs its own approach, and it is worth deciding early which face gets chalk and which gets markers, since chalk dust drifts onto anything below it.

Chalkboard Side

Roll on two or three thin coats of chalkboard paint with a foam roller, sanding lightly with 220 grit between coats. Many brands ask you to wait about three days before writing on it. Then “season” the surface: rub the side of a stick of chalk over the entire panel and wipe it off. Skipping this step can leave the first drawing permanently ghosted into the paint.

Magnetic Side

Magnetic primer contains iron particles, but it is weak. It usually needs three to four coats to hold a light fridge magnet, and it will not hold heavy letters or thick shapes. A stronger option is to glue a thin galvanized steel sheet to the panel with construction adhesive, file the edges smooth and cover them with edge trim or wide tape. You can paint chalkboard paint over either base to get a board that takes both chalk and magnets.

Dry-Erase Side

Dry-erase paints exist, but a cheaper route is a sheet of white hardboard sold as “tileboard” or “panel board” at home centers, which often wipes clean with dry-erase markers. Cut it to size and mount it like the other panels. Test a small corner with a marker first, since finishes vary between batches.

How to Make a Cardboard Easel

If you are searching for how to make a cardboard easel, the tabletop triangle is the most stable shape you can fold from a single sheet. It stands on its own, leans back at a comfortable angle and stores flat if you design it to.

Cardboard Materials

  • One sheet of double-wall corrugated cardboard at least 18 x 40 inches (an appliance or furniture box works well)
  • Steel ruler and a sharp box cutter
  • A blunt butter knife or empty ballpoint pen for scoring
  • Wide packing tape or duct tape
  • Hot glue gun or white craft glue
  • Two large binder clips
  • Optional: clear contact paper to waterproof the front face

Step 1: Mark the Panels (5 minutes)

Draw a rectangle 18 inches tall by 40 inches long, with the corrugation channels running vertically. That direction matters: cardboard bends easily along the channels and resists bending across them, so vertical channels keep the face stiff. Divide the length into three panels of 14, 14 and 10 inches, plus a 2 inch tab at the end.

Step 2: Score and Fold (10 minutes)

Run a dull blade or empty pen firmly along each fold line on what will become the inside. Scoring crushes the layers so the fold goes exactly where you want. Fold the sheet into a triangle: the two 14 inch panels form the front and back, and the 10 inch panel becomes the base. This gives a leaning face at roughly 70 degrees, which is close to the angle many tabletop easels use.

Step 3: Glue the Seam (10 minutes, plus 15 minutes setting)

Run hot glue along the 2 inch tab and press it to the inside of the opposite edge. Wrap the outside seam with packing tape. An adult should handle the hot glue. If you are using white glue instead, clamp the seam with clothespins and let it set for at least an hour.

Step 4: Add a Ledge and Clips (15 minutes)

Cut a strip 3 x 14 inches, score it lengthwise down the middle, and fold it into an L. Glue one leg of the L to the bottom of the front face so the other leg sticks out as a ledge for crayons. Slip two binder clips over the top edge of the face to hold paper.

Step 5: Protect the Face (optional, 10 minutes)

Cover the front face with clear contact paper. It will not make the easel waterproof, but it stops watercolor and tempera from soaking straight into the board, which is what causes the face to buckle.

Cardboard Variation: The Fold-Flat Easel

If storage is tight, skip the glued seam. Instead, cut two slots near the bottom of the front and back panels and make a removable base strip with matching tabs. The child slides the base in to stand the easel up and pulls it out to fold it flat behind a bookcase.

Safety Checks Before First Use

  • Tip test: Push the top of the wooden easel sideways with moderate force. It should rock, not fall. If it tips, widen the leg spread or add weight to the tray.
  • Pinch points: The hinge gap at the top can catch small fingers when the frame folds. Cover it with a strip of fabric or keep the easel open with the chain fixed.
  • Splinters: Run a bare hand over every edge. If anything catches skin, sand it again.
  • Small parts: Screw eyes, clips and magnets are choking hazards for children under three. Check they are secure and keep loose magnets away from toddlers entirely.
  • Cutters and glue guns: Keep these adult-only, even when the child is helping decorate.

Magnets deserve extra care for very young kids. The guide on whether magnetic easels suit toddlers covers age and supervision in more detail.

Common Mistakes and How to Avoid Them

Building to a Plan Written for Adults

Many free easel plans online are for adult painters, with legs of 60 inches or more. Scaled down without thought, they put the tray too high and the board too steep. Always work from your child’s elbow and head measurements, not from the plan.

No Splay Stop

An A-frame without a chain or brace looks fine until a child hangs on the tray. Then the legs slide apart on a smooth floor and the whole frame drops. Add the chain even if the easel feels steady in the garage.

Painting Chalkboard Over Raw Hardboard

Raw hardboard drinks paint unevenly and leaves a blotchy surface that chalk skips across. A coat of primer first gives the chalkboard paint an even base.

Cardboard With Horizontal Channels

If the corrugation runs side to side on the face, the panel will bend inward the first time a child presses a marker into it. Re-cut with the channels vertical.

Rushing the Cure

Water-based finishes often feel dry in an hour but stay soft for days. Paint cups set on a soft finish leave rings, and tape pulls the topcoat off. Wait the full cure time.

Making It Grow With Your Child

A fixed-height easel can feel too low within a couple of years. Three simple tricks extend its life:

  1. Adjustable tray: Instead of screwing the tray to the legs, drill a series of holes about 2 inches apart up each leg and hang the tray on short dowels. Move it up as the child grows.
  2. Riser blocks: Cut four 3 inch blocks with a shallow socket for each leg. Adding them raises the whole easel without rebuilding.
  3. Removable panel: Hang the panel on two screws and keyhole slots so you can swap a chalkboard face for a larger paper board later.

A paper roll holder is the other common upgrade. A length of dowel set into two brackets at the top of the frame lets the child pull down fresh paper and tear it off against a strip of wood with a straight edge.

Homemade vs Store-Bought: What You Gain and Lose

A homemade easel wins on cost if you already own tools and have offcuts, and it lets you size everything to your child. It also makes a good weekend project, and children who help decorate it often treat it as their own.

Commercial easels tend to win on the details that are fiddly at home: factory-adjustable legs, built-in paper roll holders, integrated storage bins, magnetic boards with a proper steel layer and a dry-erase face that does not ghost. When you add up lumber, hardware, chalkboard paint, steel sheet and finish, the material cost of a fully featured DIY easel can come close to an entry-level ready-made one. If you want those features without the build, compare the options in our guide to the best magnetic-board easels for children.

FAQs

What is the best wood for a child’s easel?

Pine is the usual choice because it is light, cheap and easy to cut and sand. Poplar is a little harder and resists dents better. For panels, 1/4 inch hardboard or birch plywood stays flat and takes paint evenly.

How tall should a kids easel be?

Set the paint tray near the child’s elbow height and the top of the drawing panel at or slightly above the top of their head. For many preschoolers that means an overall easel height of roughly 38 to 44 inches.

How do you make a cardboard easel stand up?

Fold the cardboard into a triangle with a flat base panel, run the corrugation channels vertically on the face and glue or tape the seam firmly. The triangle shape spreads the load and resists tipping without any other support.

Is chalkboard paint safe for kids’ furniture?

Many water-based chalkboard paints are low in VOCs, but formulas vary. Check the label for suitability on children’s items, let the paint cure fully and keep it off surfaces a toddler might chew.

Can I make a magnetic easel at home?

Yes. Several coats of magnetic primer will hold light magnets, but a thin galvanized steel sheet glued to the panel holds much better. Either can be painted over with chalkboard paint.

How long does it take to make a child’s easel?

A cardboard easel takes about 30 to 60 minutes. A wooden A-frame takes roughly 3 to 4 hours of work, plus one to three days for paint and chalkboard finishes to cure.

Next Step

If the build list looks longer than your free weekend, or you want a steel-backed magnetic face and a dry-erase side that wipe clean for years, look at the ready-made models in our comparison of children’s easels with built-in magnetic boards. Use the elbow and head measurements from this guide to check each model’s height range before you choose.

Facebook
Pinterest
Twitter
LinkedIn
Reddit
Telegram
Picture of Md Jomiruddin Sobuj

Md Jomiruddin Sobuj

Md Jomiruddin Sobuj is the founder and editor of PaintingProGuide. He comes to art supplies from digital publishing rather than from a studio, and the site reflects that: every guide here is built from manufacturer specifications, product documentation and the patterns that show up across hundreds of real user reviews — the details that predict how a brush, a paint or an easel actually behaves once you are using it. He writes or edits every article on the site and is accountable for what each one says, including telling you when a product is wrong for you. Corrections and questions are genuinely welcome at contact@paintingproguide.com.

Related Post

Kids paint aprons and smocks compared by age, material and pack size,
A line-by-line look at Grumbacher oil paints, who each suits, how to
A step-by-step method for soft, realistic sponged clouds, with color mixes, cloud
Build a sturdy wooden A-frame or a 45-minute cardboard tabletop easel, sized
Picture of Paintingproguide

Paintingproguide

Painting

Welcome to PaintingProGuide, your ultimate resource for all things related to painting! Whether you’re a seasoned artist or just starting out, our mission is to inspire, educate, and empower you to create your best work. We believe that everyone has the potential to be an artist, and our goal is to help you unlock your creativity and achieve your artistic dreams.

Recent Posts