A pochade box is a shallow wooden case whose lid holds a small painting panel upright while the base serves as a palette and paint store. That simple layout is why so many plein air painters build their own. If you are wondering how to make a pochade box, the core project is a shallow hinged tray with a panel holder in the lid, a lift-out palette in the base, a way to hold the lid at an angle, and a tripod socket underneath. With basic hand tools and a weekend, you can build one sized exactly for the panels you paint on.
Quick answer: Build two shallow frames from 1/2-inch solid wood, a deeper one for the base and a shallower one for the lid, and close each with 1/4-inch plywood. Join them with a piano hinge, add lid stays or friction hinges so the lid holds at a painting angle, fit a ledge and clips in the lid to grip the panel, set a sealed plywood palette on cleats inside the base, and install a 1/4″-20 threaded insert underneath for a tripod. Seal everything with shellac or oil. Plan on a weekend plus drying time.
This guide gives a complete cut list for an 8 x 10 panel box, step-by-step assembly with timings, hardware choices and the mistakes that make homemade boxes wobble or warp. If you finish reading and decide your time is better spent painting than building, our comparison of ready-made pochade boxes with tripods is a good place to weigh the alternative.
Decide on the Design Before You Cut
Three common layouts suit different ways of working. Pick one first, because it determines every dimension.
Thumb box
A small box, often for 5 x 7 or 6 x 8 panels, held in one hand by a thumb hole through the bottom while you paint with the other. Light and fast, but your palette space is tiny and your arm tires on longer sessions.
Tripod box
A slightly larger box, usually for 8 x 10 up to 9 x 12 panels, mounted on a camera tripod. Hands are free, the palette is larger and you can stand comfortably. This is the design the build below follows.
Lap or table box
A box that sits on your knees or a car hood with no mount. It needs a heavier base or rubber feet so it does not slide. Good for painting from a vehicle or a bench.
Whatever you choose, use this sizing rule: the lid interior should be the panel size plus about 1 inch on each side for clips and finger room, and the base depth should be enough to store your paint tubes lying flat under the palette, typically 1-3/4 to 2 inches inside.
Materials and Tools
Wood
- About 6 feet of 1/2 x 2 inch poplar, pine or basswood strip for the base sides
- About 4 feet of 1/2 x 1 inch strip of the same wood for the lid sides
- One piece of 1/4-inch Baltic birch plywood, at least 13 x 23 inches, for the base bottom and lid top
- One piece of 1/8-inch or 1/4-inch plywood, about 12 x 10 inches, for the palette
- Scrap strips about 1/4 x 1/2 inch for palette cleats and the panel ledge
- A hardwood block, about 3 x 3 x 1/2 inches, to reinforce the tripod mount
Hardware
- A 12-inch piano hinge (continuous hinge) with screws
- Two lid stays, or a pair of friction (torque) hinges in place of the piano hinge
- Two draw latches or box catches
- A 1/4″-20 threaded insert for wood
- Two or three turn buttons or a spring-loaded panel clip
- A carry handle (optional)
Supplies
- Wood glue and small brads or pins
- Sandpaper in 120 and 220 grit
- Shellac, oil-based polyurethane, or a drying oil such as tung or linseed for finish
Tools
- Fine-tooth handsaw and miter box, or a table or miter saw
- Drill with bits and a countersink
- Square, tape measure and pencil
- Four or more clamps (spring clamps are fine)
- Small screwdrivers and a hammer
Cut List for an 8 x 10 Panel Box
The box below has an outside footprint of 13 x 11 inches. The lid interior is 12 x 10 inches, giving an 8 x 10 panel a 1-inch margin in landscape orientation. Adjust all lengths if you work at a different panel size.
| Part | Qty | Material | Size |
|---|---|---|---|
| Base front and back | 2 | 1/2 x 2 in strip | 13 in long |
| Base ends | 2 | 1/2 x 2 in strip | 10 in long |
| Lid front and back | 2 | 1/2 x 1 in strip | 13 in long |
| Lid ends | 2 | 1/2 x 1 in strip | 10 in long |
| Base bottom | 1 | 1/4 in plywood | 13 x 11 in |
| Lid top | 1 | 1/4 in plywood | 13 x 11 in |
| Palette | 1 | 1/8 or 1/4 in plywood | about 11-7/8 x 9-7/8 in |
| Palette cleats | 2 | 1/4 x 1/2 in strip | 9 in long |
| Panel ledge | 1 | 1/4 x 1/2 in strip | 11 in long |
| Mount block | 1 | hardwood | 3 x 3 x 1/2 in |
The frame uses simple butt joints: the 13-inch pieces run full length and the 10-inch ends fit between them, which gives a 13 x 11 outside dimension. Measure your actual strip thickness before cutting the ends, since “1/2 inch” stock is often slightly under. The ends should equal the outside depth minus two times the true thickness.
Step-by-Step: How to Make a Pochade Box
Cut all parts (about 1 hour). Cut the strips to length first, checking each end for square. Then cut the two plywood panels. Label everything with masking tape so lid and base parts do not get mixed up.
Assemble the base frame (20 minutes, plus glue set). Glue the 10-inch ends between the 13-inch front and back. Pin each corner with two small brads, check the diagonals are equal so the frame is square, and clamp. Let the glue set for about an hour before handling.
Assemble the lid frame the same way (20 minutes, plus glue set). Use the 1-inch strips. Check square carefully, because a twisted lid will never close flat against the base.
Attach the plywood panels (30 minutes, plus overnight cure). Spread glue along the bottom edge of each frame, lay the plywood on, align the edges and pin every 3 to 4 inches. Weight both assemblies on a flat surface and let them cure overnight. Plywood glued to a frame on a flat surface stays flat; plywood that cures on an uneven table can lock in a twist.
Sand and fit (30 minutes). Flush any overhang with 120-grit paper on a block. Lay the lid on the base and check that the edges meet all the way around. Sand high spots until they do. Finish with 220 grit and ease all sharp edges.
Install the panel ledge and clips in the lid (20 minutes). Glue the 11-inch ledge strip across the inside of the lid about 1 inch up from the hinge edge. This is what the bottom of your panel rests on. At the opposite edge, fit two turn buttons or a spring clip that swings over the panel’s top edge. Test with a real panel; it should sit snugly with no rattle. Thin panels and thicker canvas boards differ, so allow for both if you use both.
Fit the palette cleats in the base (15 minutes). Glue the two cleats to the inside of the base ends, about 1/2 inch below the top rim. The palette rests on them, leaving room underneath for tubes, brushes and a rag. Cut a finger notch in one edge of the palette so you can lift it out.
Reinforce and install the tripod mount (30 minutes, plus glue cure). Set up the box open, with a panel in the lid, and balance it on a pencil to find its center of gravity. Mark it on the underside. On most boxes it sits a little toward the hinge side. Glue the hardwood block inside the base over that mark, let it cure, then drill through and install the 1/4″-20 threaded insert from underneath. Detailed mounting advice, including washers and quick-release plates, is in our guide on attaching a pochade box to a tripod securely.
Hang the lid (30 minutes). Clamp the closed box with the back edges flush. Lay the piano hinge along the back, mark and drill pilot holes, and drive the screws. Pilot holes are essential; screws driven straight into 1/2-inch stock can split it.
Add lid stays (20 minutes). Mount a stay on each side so the lid locks at roughly 100 to 110 degrees open, which tilts the panel back slightly for comfortable painting. Adjustable stays or friction hinges let you change the angle for glare. If you used friction hinges instead of a piano hinge, check they are rated for the weight of the lid plus a panel.
Fit the latches and handle (15 minutes). Place latches on the front, close to each corner. Mount the handle on the front or on one end, wherever the box balances when carried closed.
Finish (1 to 3 days including drying). Remove the hardware. Apply two or three thin coats of shellac or oil-based polyurethane to all surfaces, inside and out, sanding lightly between coats. Finishing both sides equally reduces warping. Seal the palette separately with several coats of drying oil, letting each dry fully. Reinstall hardware once everything is dry.
Preparing the Palette Surface
The palette takes the most abuse, so give it extra attention.
Oiled wood is traditional for oil painters. Rub in a thin coat of linseed or tung oil, wipe off every bit of excess, and let it dry for several days. Repeat three or four times. The result is a smooth, warm-toned surface that cleans with a rag.
Gray-toned surfaces help many painters judge value, since a mid-gray background makes mixed colors easier to read than bright wood or white. You can tint the final coats or paint the palette a neutral gray with a durable enamel before sealing.
Glass or acrylic inserts cut to fit over the palette board make scraping easy. Glass is the easier to clean, but it is heavier and should have sanded edges. Acrylic is light but scratches with a palette knife.
For acrylic painters, a stay-wet palette insert, essentially a shallow tray with a damp sponge and membrane paper, can replace the wood palette entirely. Make the base slightly deeper if you plan to do this.
Common Build Mistakes
Putting the tripod mount at the geometric center
The open lid with a wet panel shifts the weight back toward the hinge. A mount at the center of the closed box leaves the open box unbalanced, which makes the tripod head creep. Always find the balance point with the box open and loaded.
Using thin plywood for the mount
A threaded insert in 1/4-inch plywood will eventually pull out. The hardwood backing block is not optional on a tripod box.
Ignoring wet-panel storage
Many painters want to carry a finished, wet panel home. Consider making the lid deeper, about 1-1/2 inches, and adding a second set of grooves or turn buttons so one panel can be stored face-in with an air gap, or plan for a separate wet-panel carrier.
Overbuilding
Solid hardwood sides, brass hardware and a thick glass palette all add weight. A box that is pleasant in the workshop can be tiring after a mile of trail. Poplar and Baltic birch plywood offer a good balance of strength and lightness.
Skipping the finish inside
Raw wood soaks up solvent and oil, and moisture from damp mornings swells it unevenly. Seal every surface.
Build It or Buy It?
| Factor | DIY pochade box | Commercial pochade box |
|---|---|---|
| Fit to your panels | Exact; build to any size | Limited to the sizes offered |
| Time | A weekend plus drying | Ready to paint on arrival |
| Tools needed | Saw, drill, clamps | None |
| Lid angle and stays | Depends on hardware you source | Engineered and adjustable on many models |
| Tripod integration | You place and install the mount | Socket or bracket built in; some include a tripod |
| Wet panel storage | Only if you design it in | Common on mid-range and up |
| Weight | Varies with your material choices | Often optimized and stated |
| Satisfaction | High if you enjoy building | High if you want to paint now |
A homemade box makes the most sense if you already have tools, paint at an unusual panel size, or want to experiment with a layout before spending on a commercial one. If the hardware sourcing and fiddly fitting sound like a chore, a manufactured box with a matching tripod gets you outdoors sooner.
Choosing a Tripod for Your Homemade Box
Your finished box, loaded with paint, a panel and solvent, may weigh more than you expect. Weigh it fully loaded on a bathroom scale, then choose a tripod and head with a rated load comfortably above that number, because the open lid puts the weight off-center. Pan-tilt heads with independent locks tend to hold an off-center box more steadily than small ball heads. Our buying guide on what tripod you need for a pochade box covers load ratings, leg locks and heads in detail.
Variations Worth Considering
- Side wings. Hinged or sliding shelves on each side of the base extend the palette area for larger mixes. Fit them with small folding brackets.
- Brush slot. A strip with drilled holes along one end of the base holds brushes upright and keeps wet bristles off the palette.
- Solvent cup holder. A clip or a shallow hole in a wing for a small lidded cup reduces spills.
- Adjustable panel holder. Replace the fixed ledge with a sliding bar in grooves so the lid can hold 6 x 8, 8 x 10 and 9 x 12 panels.
- Cigar box conversion. For a 5 x 7 thumb box, a sturdy wooden cigar box with a ledge glued in the lid and a thumb hole in the bottom is a fast starter project.
FAQs
What wood is best for making a pochade box?
Poplar, pine or basswood strips for the sides and Baltic birch plywood for the top and bottom are a popular mix. They are light, stable and easy to work. Hardwoods like cherry or walnut look beautiful but add noticeable weight.
What size should a homemade pochade box be?
Size the lid interior to your panel plus about 1 inch on each side. For an 8 x 10 panel, an outside footprint near 13 x 11 inches works well. Thumb boxes for 5 x 7 or 6 x 8 panels are smaller and lighter.
How do you hold a pochade box lid at an angle?
Use a pair of lid stays mounted on each side, or replace the standard hinge with friction hinges rated for the lid’s weight. Both let the lid stay open at a slight backward tilt, typically around 100 to 110 degrees.
Can I make a pochade box without power tools?
Yes. A fine-tooth handsaw with a miter box, a hand drill or brace, clamps and glue are enough. Accurate, square cuts matter more than the tools, so take time measuring and checking corners.
How do I add a tripod mount to a pochade box?
Glue a hardwood block inside the base at the open box’s balance point, then drill and install a 1/4″-20 threaded insert from underneath. That thread matches standard camera tripods and most quick-release plates.
Is it cheaper to make or buy a pochade box?
Materials for a simple homemade box usually cost less than a commercial one, especially if you have scrap wood and tools. Once you add good hinges, stays, latches and your time, the savings narrow, and a bought box often includes features that are hard to make.
Next Step
Build one if the project appeals to you, or use what you have learned here as a checklist for judging manufactured boxes: panel holding, lid angle, palette size, weight and tripod mounting. To compare finished options against your DIY plans, see our guide to the best pochade box and tripod combinations for plein air painting.



